CoreAlign — Live Shutter Position Monitoring

Shaft / core

Lift Shaft 1 (south-west)

Construction height

17,750 mm

Section

#6 complete

Cycle

18420

Camera frame spread

—

Last valid position

unavailable

Motion

SETTLED · 0.00 mm RMS

Coordinate system

Embassy Gardens site grid (local, mm)

POSITION NOT VERIFIED

Awaiting first camera read cycle from CoreAlign Gateway.

— No position has been calculated yet.

Demonstration thresholds in use (0–10 normal, 10–15 warning, 15–20 high, 20–25 critical, 25 mm+ outside permitted tolerance). Real thresholds must be configured and approved by the project's competent engineer or surveyor.

X deviation

—mm

Y deviation

—mm

Total horizontal

—mm

Permitted 25 mm

Z deviation

—mm

Worst laser residual

—mm

Pitch

—°

Limit ±0.15°

Roll

—°

Limit ±0.15°

Yaw

—°

Limit ±0.25°

Pose quality

—

0 lasers used · RMS — mm

Tilt sensor (source of pitch/roll)

—° p/r

Top-down view — plan

— design shaft / shutter, laser heads— measured shutter + plates— tolerance boundary (25 mm)Spots read this cycle: 0

Deviation visually exaggerated ×40 — numerical measurements are actual.

Elevation — North / South (pitch)0.000°

Reference wall 2000 mm · current elevation 0 mm · exaggerated ×40

Elevation — East / West (roll)0.000°

Reference wall 2000 mm · current elevation 0 mm · exaggerated ×40

Laser channels — spot position on each plateResidual limit 4 mm

Laser / plate	Spot U	Spot V	Off centre	Edge margin	Spot Ø	Fit residual	Read at	Age	Status
L1 PL-L1 · CAM-L1	—	—	—	—	—	not used	—	—	NO SPOT — BEAM BLOCKED
L2 PL-L2 · CAM-L2	—	—	—	—	—	not used	—	—	NO SPOT — BEAM BLOCKED
L3 PL-L3 · CAM-L3	—	—	—	—	—	not used	—	—	NO SPOT — BEAM BLOCKED
L4 PL-L4 · CAM-L4	—	—	—	—	—	not used	—	—	NO SPOT — BEAM BLOCKED

U and V are the measured spot offsets from the plate centre, in plate axes. Residuals compare each spot against the best-fit shutter position. Excluding a reading never deletes it — the original record and the reason are retained in the audit trail.

Live trend — horizontal deviationCollecting samples…

Start a climb to record trend samples.

Jack cycle & vibrationVIB-01 —

SETTLED — SURVEY DATA TRUSTED

Structure quiet for 0 s since the last stroke. Positions are averaged over settled cycles.

Vibration amplitude0.00 mm RMS · —

Measurement limit 0.35 mmAlarm 1.2 mm

Stroke height

40 mm

Next stroke in

—

Strokes this shift

Risen today

0 / 3000 mm

Settled position (averaged over quiet cycles)

No settled cycle yet — awaiting a quiet measurement.

Climb mode

PASSCoreAlign Gateway online
PASSPlate cameras online
FAILSufficient laser readings (≥ 4)
PASSLaser setout verified against control
FAILTilt sensor INC-01 online
FAILCross-check tilt sensor INC-02 online
FAILMeasurement quality acceptable
FAILCurrent position established
PASSStructure settled (vibration ≤ 0.35 mm RMS)
FAILVibration sensor online

PRE-CLIMB CHECKS NOT SATISFIED

Alerts0 active

No active alerts against configured limits.

Hydraulic lift pointsSYNCHRONISED

Point	Δ average	Status
J1 NW	+0.0 mm	ok
J2 N	+0.0 mm	ok
J3 NE	+0.0 mm	ok
J4 SE	+0.0 mm	ok
J5 S	+0.0 mm	ok
J6 SW	+0.0 mm	ok